Specification:

Emitter: 3pcs XHP50.2LED, Cold white, Mounted on copper DTP MCPCB.
Flux: 6500 lumens or 10000lumens when using 1pcs 26650 battery.
Intensity: 20500cd(ANSI throw: 285meters) , 35000cd 375meter by using 26650 Li-ion battery.
User interface: Anduril Firmware with defaulted smooth RAMPING UI. Instant access to a TURBO mode and mode settings are also provided.
Battery: 1x 26350, max length 35.5mm or 1pcs 26650 (max length 65.5mm) via the extension tube(battery and extension tube are excluded).
Power: 45W/70W(26650)
Reflector: Aluminum OP finish
Lens: Glass with anti-reflective coating
Body: Aluminum with TYPE III hard –coat and anodizing.
Button: Tactile with back-lit rubber boot.
Weight: 96g without battery
Size: 40*76*30mm(head*length*tube)

Operation Instruction

1 click:Memorized level

Hold:lowest level then ramp up

2 clicks:highest ramp level

Click,hold:highest level then ramp down

3 clicks:specials(battcheck,goodnight,beacon,tempcheck)

Click,click,hold:Strobe(candle,bike flasher,party strobe,tactical strobe,lighting storm)

4 clicks:lock-out

5 clicks:momentary mode(disconnect power exit)

6 clicks:Muggle mode

7 clicks:Aux button led low/flash/off

In steady mode

1 click:off

Hold:ramp up

Click,hold:ramp dorm

2 clicks:turbo

3 clicks:toggle smooth vs discrte ramping

4 clicks:configure the current ramp

Ramp configuration mode

Setting 1:Floor(click N times to level N)

Setting 2:Ceilng(click N times for 1+Turbo N)

Setting 3:Set number of steps(stepped ramping only,click N times to set N levels)

Strobe group modes:

Candle Mode

1 click:off

2 clicks:next strobe group mode

3 clicks:add 30 minutes to the timer(light will shut off when the timer ecpires,defaults is no timer)

Hold:brighter

Click,hold:dimmer

Biker flasher

1 click:off

2 clicks:next strobe group mode

Hold:brighter

Click,hold:dimmer

Party/Tactical Strobe Modes

1 click:off

Hold:change speed,faster

Click,hold:change speed,slower

2 clicks:next strobe group mode

Lighting Strom Mode

1 click:off

2 clicks:next strobe group mode

Blinky group modes:

Battcheck Mode

1 click:off

2 clicks:Goodnight mode

Goodnight Mode

1 click:off

2 clicks:beacon mode

Beacon Mode

1 click:off

2 clicks:tempcheck mode

4 clicks:configure the time between pulses

Beacon config mode:at buzz,click N times to set beacon frequency to N seconds

Temp Check Mode

1 click:off

2 clicks:battery check mode

4 clicks:thermal calibration mode

Hold:thermal calibration mode

Thermal configuration mode

Setting 1:calibrate sensor,at buzz,click N times for N degrees.For example,if the light is current at room temperature of 22 C click 22 times,it intended to only be done once upon initial setup,or not at all.

Setting 2:temperature limit:At buzz,click N times to set a thermal limit to roughly 30C +N.

Lockout Mode

Hold:momentary moon

4 clicks:exit lockout,return to regular off mode

Momentary mode

press button:light on at the memorized level

Release button:off

To exit:disconnect the power by loosening/tighten the tail cap

Muggle Mode

1 click:on/off

Hold:ramp up/down

6 clicks:exit muggle mode

Aux button led configuration

7 clicks:change Aux led modes,low--high--flash--off

Factory reset

Loosen the tail cap,ress and hold the switch,then tighten the tail cap to make an electricty contact